HOME POOL SAFETY.
Not all Skimmer Lids were created equal. Many traditional options may miss the mark. But choosing HIDE will give you 100% peace of mind.
THE AUSTRALIAN POOL STANDARD
The backyard pool is a timeless icon of summer fun.
But there is a serious side to owning your backyard dream - pool safety.
In Australia, the safety requirements for skimmer boxes and their lids are set out in Australian Standard AS 1926.3–2010, Swimming pool safety, Part 3: Water recirculation systems.
The skimmer box is the main suction point of the pool, connected to a powerful pump. Limbs and hair can become trapped, and children are most at risk. Without proper venting, suction can also hold a child at the mouth of the skimmer box. The standard addresses both risks.
01
EVERY SKIMMER LID MUST BE VENTED
Every skimmer box lid must be vented to atmosphere, with a total clear vent area of at least 315 mm². The shape and number of vents can vary. Venting reduces the risk of a child being held at the mouth of the skimmer box by suction.
How HIDE meets it: Lifters in the HIDE Edge Protector hold the lid 5 mm above its base, so air flows freely around and under the lid. On the 342 mm Skimmer Lid, that clearance and the keyhole provide about 1,500 mm² of vent area, more than four times the minimum.
02
CHILD-RESISTANT LIDS
Where a pump draws from a single skimmer box, the standard requires at least two of these three safety measures:
- a skimmer box built to the dimensions set out in the standard
- a child-resistant lid
- an auxiliary outlet connected to the skimmer box
In practice, a pool with one skimmer box and no auxiliary outlet needs a child-resistant lid.
The standard defines a child-resistant lid as one that, once installed, either:
- cannot be lifted off vertically with a force of less than 100 newtons, or
- has a locking mechanism.
Either option meets the standard. A lock is not required.
How HIDE meets it: The HIDE lid has no grasp holes and is removed only with the HIDE Safety Key.
WHAT MAKES HIDE POOL-SAFE?
Unlocking HIDE pool safety is simple... it’s all in the design of the Safety Key!
The HIDE lid has no grasp holes and cannot be removed by hand. It is opened only with the HIDE Safety Key, which fits a small slot in the lid.
The keyhole and the clearance around the lid also provide venting well above the minimum the standard requires.
Learn how easy it is to use the key here, and be sure to read our simple instructions for safely opening and closing a HIDE lid.
ALWAYS REMEMBER – the Safety Key must be stored in a secure location, out of reach of children at all times.
THE SUPERIOR CHOICE.
- Designed to meet the venting and child resistant lid requirements of AS 1926.3, for peace of mind for families. It also sits flush with its surrounds, reducing trip hazards.
- The kit provides all a contractor needs to install onsite. It’s a quick, easy job for a professional, so can be fitted affordably.
- Durable, long-life product as the steel frames protect the inlay + surrounds, significantly reducing chipping or breakages and future batch matching headaches. Includes a 20-year warranty!
- The HIDE lid can be matched to existing grout lines, or installed with multiple landscaping materials. It blends seamlessly into your landscape, providing a luxury finish with an almost invisible key hole.
- Many pool owners have opted to upgrade to a HIDE after they experienced problems with traditional skimmer lids options, like those outlined below.
Electrical Compliance (Earthing)
All swimming pool construction and refurbishments in Australia require compliance with legislated electrical work regulations. Always consult a licensed electrician to discuss required earthing requirements.
OTHER SKIMMER LIDS CAN LEAVE YOU HIGH + DRY.
Alternative traditional skimmer lid options are unattractive, plus have quality and durability concerns which can cause serious headaches for home-owners and contractors alike. What’s worse, is that many don’t even meet Australian Pool Safety Standards! On a pool journey, you’ll typically encounter two other skimmer lid options:
THE PLASTIC OPTION.
The traditional cheap, plastic lid which needs to be replaced regularly due to sun damage and wear.
- Cheap looking, unattractive finish which detracts from the beauty of the pool-scape ie raised, bulky, quickly discolours in the sun.
- Sun exposure makes the plastic brittle and susceptible to cracks and breakage, requiring replacement.
- The raised lid can be a trip hazard, especially for young children.
- The lid colour can’t be matched to the paving, and grout lines are interrupted.
- Requires regular replacement due to constant load-bearing damage if it is located on a main walkway around the pool.
THE LOOSE STONE/TILE OPTION.
A brittle option which is both unattractive and often short-lived. They usually break quickly, or cause chipping or damage to the surrounding stone.
A loose stone is often NOT compliant or POOL SAFE.
- The finger holes make moving the loose stone difficult without chipping, cracking or breaking the stone itself, or the surrounds.
- The brittle stone is easily damaged and matching new stone to existing stone is difficult, as batches change or are discontinued.
- A contractor has to be recalled, usually at the homeowners expense, to match, cut + fit a new stone (which often remains non-compliant).
- Cheap looking finish with large holes, interrupted grout lines and the stone often doesn’t sit flush with the surrounds creating a tripping hazard.
- Non-compliance issues mean young children are at risk of serious harm. The stone is usually less than 10.2kg in weight, it is loosely fitted, and the finger holes are typically quite large. This means a child can access the skimmer basket, so it does not meet the national skimmer standards.
CAN I REPLACE MY PLASTIC OR LOOSE STONE LID WITH A HIDE?
HIDE skimmer lids (or any HIDE lid!) can usually be easily retrofitted to replace other lid options. In fact, since our launch, many pool owners have opted to upgrade to a HIDE due to ongoing problems with traditional lid types.
HIDE can be retrofitted into landscapes with pavers, tiles, decking or concrete. If using a paver/tile, you will need a spare to insert into the inlay lid. If you don’t have a spare we can help source one that is a close match to your existing tile/pavers.
I WANT A HIDE IN A DIFFERENT SIZE!
Usually your contractor can cut a new recess in your landscape area to retrofit a HIDE in one of our standard sizes. However, if our available size options do not match the recess area for your lid – don’t stress!
HIDE can manufacture custom-sized lids for skimmers, drain and access points. We will happily guide you through the custom manufacturing process.



